Walkthrough
Port forwarding on a router with NordVPN: what the result depends on
Checking port forwarding on a router while NordVPN is active requires taking account of where the VPN runs and the route taken by the reply from the target device. You can clarify NordVPN's position on inbound connections through its servers in the service's official help documentation. To carry out the check you will need the router model and firmware, access to its admin panel, and access to the settings of the device accepting the connection.
5 min readUpdated Published by VPN for Devices
How the place where the VPN runs affects port forwarding
The table below helps to break down the connection scheme. The place where the VPN runs does not by itself guarantee that the service will be reachable from outside.
| Scheme | Where the VPN runs | Where the connection arrives | How the reply leaves | What determines the result |
|---|---|---|---|---|
| NordVPN only on another device; the VPN client on the target device is switched off | Another PC or phone | On the router's WAN, then to the target device | According to the routes of the target device and the router | External reachability of the router, the forwarding rule and the firewall |
| NordVPN on the target PC or NAS | Target device | On the router's WAN, then to the device according to the forwarding rule | Depends on the device's routes: the reply may leave through the VPN | The return route, exclusions from the tunnel and firewall rules |
| VPN on the router, all traffic inside the tunnel | Router | On the router's WAN | May leave through the tunnel | Consistency between the inbound route and the return route |
| Service routed through the ordinary WAN | Router with route selection | On the router's WAN | Through the WAN, if this is provided for by the rules | The router's routes and those of the target device, reachability of the service |
| Connection requested through the VPN address | Router or device | On the address of the VPN server | Along the configured VPN route | Inbound access conditions set by the VPN provider |
1. Initial parameters: determine your scheme
First find out the router model, the firmware version and compatibility with a VPN client. Then gather the details of the connection:
- Establish where NordVPN is running: on the router, on the target device, or on another device in the network.
- Clarify which connection protocol has been chosen.
- Determine the device and service that must accept connections from outside.
- Check with your internet provider whether inbound access to your connection is available.
Also record the address to which the external client should connect: the address of your home connection or the VPN address. These are different schemes, and the home router's rule by itself does not define the conditions for access through the VPN server.
2. Settings: check the route before changing rules
Model example: a PC with a game server or a NAS is connected to a TP-Link router. TP-Link's documentation describes routing selected devices through the VPN client for supported models. Whether this feature applies needs to be verified against the model and firmware of your router.
- Check whether NordVPN is running directly on the target PC or NAS.
- Compare the rules for selecting devices for the VPN against the router manual.
- Check the return route and firewall rules of the target device.
- Temporarily switch off the local VPN client for a diagnostic comparison of reachability from outside.
Excluding a device from the VPN on the router does not switch off the VPN client on the device itself. The result of the comparison helps to narrow down the cause of the fault, but it does not guarantee that an inbound connection will work once the client has been switched off.
3. If it does not work: match the cause to the action
If the reply leaves through a different interface, check the routes on the router and on the target device. With two VPN clients, changing only one of them may leave the original problem in place.
If the connection is being blocked on the PC or NAS, check the firewall and whether the service accepts connections from the network. Do not switch off protection entirely just to open up one service.
If the external client addresses the VPN address, compare the inbound access conditions against the official NordVPN help documentation. If the home connection address is used, clarify inbound access restrictions with your internet provider.
4. Verifying the result: confirm access from outside
Test the required service from an external network, for example via mobile data, under the VPN configuration you intend to use. Record the result with the local VPN client enabled and without it, keeping the other conditions of the comparison unchanged.
A changed external IP or a normal download speed does not confirm that the inbound port is reachable. Treat the scheme as working only if an external client actually connects to the required service.
Before finishing, check the following:
- NordVPN's conditions have been checked for your method of connection.
- The reply route has been verified on the router and the target device.
- The firewall permits only the necessary access.
- Connection to the service has been confirmed from an external network with the working VPN configuration enabled.
Frequently asked questions
Will things be the same with Mullvad?
The conditions for inbound connections need to be checked separately in Mullvad's official help documentation. Support for a protocol on a router does not by itself answer the question of port forwarding.
Is it safe to open a port while the VPN is enabled?
An enabled VPN does not by itself confirm the security of an exposed service. Assess who is able to connect, how authentication and the firewall are configured, and whether updates for the service have been installed.